Key Resin – Luster Metallic

KEY LUSTER METALLIC is a decorative thin-film system having a bright metallic finish. It is typically finished with a clear urethane or epoxy sealer for excellent wear and abrasion resistance. KEY LUSTER METALLIC industrial floor coatings are ideal for residential use, office complexes, commercial areas, lobbies, or light industrial applications.

We have other products and systems of which we can Engineer to fit your application. Give us a call at 801-977-0508!

SKU: item-1063 Category:
Tensile Strength (ASTM D-638)8500psi
Adhesion to Concrete (ACI Comm 403)350 psi (100% concrete failure)
Hardness (ASTM D-2240)80 Shore D
Flexural Strength (ASTM D-790)8000psi
Compressive Strength (ASTM D-695)11000psi
Wet Service Temperature150F
Dry Service Temperature160F
Maximum Water Absorption (ASTM D 670-73)0.10%
Viscosity at 75F, Mixed750 to 1000cps
Mixing Ratio4 Parts A to 1 Part B by Volume
Solids Content100%, by volume
Volatile Organic Content (VOC)-0-
Gloss, 60F100 to 110
Weight per Gallon Mixed9.00 to 9.50lb/gal
Pot Life30 to 40 minutes at 75F
Dry to Touch10 to 14 hours at 75F
Re-Coat14 to 16 hours at 75F
Light Traffic16 hours at 75F
Full Cure & Maximum Resistance5 days
Key Advantages
  • Good clarity and color.
  • Low odor during application and cure. Can be applied in occupied buildings.
  • Low viscosity. Easy spreading and wetting properties.
  • Available in “Fast Cure” Systems.
Key Considerations
  • Substrate temperature must be a minimum of 50F (Contact Key Resin Company for Low Temperature Cure).
  • Substrate must be free of dirt, waxes, curing agents, and other foreign materials.
Composition100% Solids Epoxy Resin with Aliphatic Amines and Metallic Pigments.
Surface Preparation
Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in KEY RESIN COMPANYS TECHNICAL BULLETIN 1. Work must be performed by trained or experienced contractors or maintenance personnel. The KEY RESIN COMPANY service department is pleased to answer any questions.
KEY LUSTER METALLIC is normally applied as a three or four coat system.

KEY RESIN 502 EPOXY PRIMER or KEY RESIN 535 WATER EMULSION FINISH are used to prime the surface.

KEY LUSTER METALLIC is applied in two coats spreading with a flat trowel at 100-125 square feet per gallon on each coat. The second coat is sprayed lightly with a dispersing agent to distress the surface. A seal coat of Key urethane or epoxy will provide excellent wear and abrasion.

Clean UpClean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.
Key Resins are available throughout the United States, Canada, and a number of other countries. Contact the KEY REPRESENTATIVE in your area for details.
After completing the application of KEY LUSTER METALLIC, the installer should provide the owner with maintenance instructions. If floors become slippery due to animal fats, oil, grease, or soap film, clean and rinse thoroughly.

KEY LUSTER METALLIC is easily cleaned with neutral soaps or detergents. Routine mechanical scrubbing is recommended for all surfaces having a non-skid texture. Waxing is optional. Long periods of heavy traffic may cause wear patterns necessitating a maintenance application of a finish coat.

Technical Service
Key Resin Company and KRC Associates, Inc. provide services and consultations on material selection, specification, troubleshooting, and other information on the proper repair and protection of concrete surfaces. KEY REPRESENTATIVES are available to assist you at any time.
Key Resin Company (“Key”) warrants for a period of one (1) year that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Key. If any product fails to meet this warranty, the liability of Key will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Key within (1) one year of delivery of materials. Key may in its discretion refund the price received by Key in lieu of replacing the material. No customer, distributor, or representative of Key is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Key. In order to obtain replacement or refund the customer must provide written notice containing full details of the nonconformity. Key reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. KEY’S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND KEY SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Request More Information